CIAT AQUALIS CALEO PDF

Tygomuro Depending on the geographic location aquxlis the type of mains network buried or overheadyou may have to install a lightning rod. Portable Evaporative Air Cooler. Faults are stored in memory during power cuts and the fault relay is stuck in a particular position. Dial selection dot 8-position operation mode dial.

Author:Ditaxe Vulmaran
Country:Japan
Language:English (Spanish)
Genre:Sex
Published (Last):9 August 2004
Pages:155
PDF File Size:17.64 Mb
ePub File Size:13.82 Mb
ISBN:357-1-27300-142-2
Downloads:52462
Price:Free* [*Free Regsitration Required]
Uploader:Mauhn



Neran To do so, simply loosen the nut measure on the bottom of the pressure switch approx. Failure to comply with the requirements of the above standards will void the CIAT warranty.

Stage-1 electric auxiliary unit operation Indicator 4: R L Always comply with the appropriate bend radius. Location in room The terminal should be installed at a recommended height of 1. However, special applications e. Do not tighten these screws to a torque of greater than 1 Nm. With the thought of material improvement always in mind, CIAT reserves the right, without notice, to proceed with any technical modification.

English Cist 1 1 Remove the middle screw rear of unit 2 Detach both ends as shown in picture 3 Remove of the top by sliding it toward the rear Ciwt e u t s ch — The characteristics of the mains supply must be identical to those on the data plate. Clean the drain pan. Prices are indicative only and may vary by country, with changes in raw materials prices or exchange rates. Although it calwo rain resistant, it may be installed under a shelter with adequate ventilation on all four sides.

Access to level-2 installer settings For further information on reading and programming the terminal, refer to the manual provided with it. It may be necessary to use them when starting the caleeo or when turning it off for extended periods of time. Electrical connection tightness check Outdoor coil cleaning Control check Differential water pressure switch Status of liquid sight glass and leak detection 44 5.

L Always top up with the same type of mix initially used. Insulate the pipes and hoses carefully to prevent heat loss and condensation. English Installation D e u t s ch — Settings stored in cakeo for two hours following a power cut — Blue backlit digital display — Maximum dimensions: Controlled by dry contact J1 D e u t s ch In all three cases, the circulator can be started back up to protect the exchanger from freezing temperatures.

This can be minimised by following two rules: Moreover, a d3 fault water flow rate fault must not prevent the boiler from operating. It is your responsibility to protect the unit from mains voltage spikes and voltage spikes caused by lightning. Turn the terminal dial to one of the following positions: If water installation capacity superior to the values indicated in the technical characteristics table chap 7. Remove the top as shown in Figure 1 and make a connection to terminal block J1 on aquualis PSU board the one with the contactor.

To access the settings, do as follows: Then attach the mounting plate to a wall using the screws and anchor bolts or a flush-mount box 60 mm centre distance using the holes Fig. With the unit running, check it thoroughly for any abnormal visual signs or noises. L If you have a radiant floor heating system, only use pressurised neutral gas compressed air, nitrogen to blow out the water remaining in the water loops.

To do so, first insert the tabs Fig. Only qualified personnel may calro the settings. Do not tighten these screws to a torque of greater than 13 Nm. Check for any loose electrical connections. Stage-2 electric auxiliary unit operation Indicator 3: Only experienced and qualified persons may work on this equipment. The Online Industrial Exhibition. The predominant problem with outdoor units is disturbance caused to the neighbourhood because of noise.

Protect from prevailing winds. English The differential water pressure switch is a safety component. D e u t s ch Connection diagrams schematic diagrams English To protect your heating system and avoid all risks of it freezing should it be intentionally or accidentally turned off, we strongly advise that you: D e u t s ch — Open the valves on the water circuits and make sure water is flowing through the heat pump.

If this is not the case, follow the procedure below: Selecting a location In most cases, the control terminal should be placed in the room in which the atmosphere is to be controlled. The diameters of the tubes are not necessarily the same as those of the unit. A 3 bar safety valve must be placed on the water loop. Heat pump and boiler operating ranges: Italiano — Three-way valve 54 6. TOP Related Posts.

AWARIF UL MAARIF ENGLISH PDF

anabolicsteroids.me

Mutilar It is therefore strictly prohibited to bypass it; doing so will create a safety hazard to property and people. Insulate the filter or install it indoors protect from freezing temperatures. Hoses must be used to connect the water pipes to limit as far as possible the vibrations transmitted to the building. These instructions covers the installation of replacement coil kit into More information. Connection — Attach the two wires to the terminal Fig. Location in room The terminal should be installed at a recommended height of 1.

BASIC CIRCUIT THEORY CHARLES DESOER PDF

CIAT AQUALIS CALEO PDF

Kazijora The predominant problem with outdoor units is disturbance caused to the neighbourhood because of noise. NF C in France and are under the responsibility of the installer. To do so, simply loosen the nut measure on the bottom of the pressure switch approx. English To protect your heating system and avoid all risks of it freezing should it be intentionally or accidentally turned off, we strongly advise that you: However, as soon as you begin designing your system, you should take into consideration the outdoor environment to estimate the radiated noise and the building type to estimate the noise transmitted through the air and by solid materials vibrations. Only experienced and qualified persons may work on this equipment. The information on the plate particularly the description and the serial number must be quoted in all correspon- D e u t s ch dence. It is therefore strictly prohibited to bypass it; doing so will create a safety hazard to property and people.

Related Articles